November 2019 to September 2025

​

NBTC (Naser Mohamed Al-Baddah Trading & Contracting Co.)

​

Established in 1977, NBTC provides civil and MEP contracting for commercial and residential buildings projects in Gulf.

Designation : Sr. Design Engineer PL/FF

Designation : Sr. Design Engineer – Plumbing and Fire Fighting

 

Spearheaded full-cycle design of fire protection and plumbing systems for high-value projects, including US Army hangars, APS-500 Warehouses (Camp Arifjan), and the F-18 Super Hornet project at Al Jaber Air Base.

Handled tendering and estimation for plumbing and firefighting systems for both the F-18 Super Hornet project and the KOC project: Construction of 72MW, 11KV Main Intake Substation at Sabriya Area.

Successfully led the design of the 35th Brigade multifunctional warehouses during tender stage, 2.5× larger than the Camp Arifjan scope, in full compliance with UFC and NFPA 13 standards.

Delivered hydraulic calculations using HASS and Elite software, optimized pipe sizing, and introduced seismic bracing design, resulting in cost savings of KD 63,000 in steel pipe layout and planning.

Played a key role in securing and executing the Jaber Air Base project with design support for the US Air Force, which yielded significant variation orders and profitability.

Supervised fire protection and Plumbing works for a 72MW, 11kV main intake substation at Sabriya KOC Project.

Led coordination with KFD for timely approvals and ensured full compliance with authority standards across all firefighting systems.

​

Major Project Highlights:

​

Construction of 72MW, 11KV Main Intake Substation at Sabriya Area, North Kuwait

​

 April 2024 - Present

​

The project included the complete supply, installation, and testing of plumbing and fire suppression systems (IG-541) for high-voltage substations and associated buildings. Scope covered internal and external water supply systems, drainage and sewage networks, sanitary fixtures, fire suppression piping and fire extinguishers systems as per KOC and NFPA standards.

I was responsible for reviewing contract drawings and specifications to ensure compliance with KOC standards. I prepared Request for Material Approval (RAM) for KOC review, developed method statements for shop fabrication of fire suppression pipe spools, and ensured implementation of approved Welding Procedure Specifications (WPS). I coordinated with the Fire Suppression subcontractor, supervised fabrication activities in the workshop, and managed the installation of fire suppression piping and plumbing systems at site. I also witnessed Factory Acceptance Tests (FAT) for fire suppression equipment and supported QA/QC inspections and documentations.

​

Project Name : Kuwait F-18 E/F Super Hornet, Al Jaber Air Base, US Air force and Navy

​

Duration: March, 2022 – June, 2025

​

This project consists of overhead wet pipe sprinkler system and foam grate nozzle system. Created Fire Protection Shop drawings for Maintenance Hanger, Corrosion Control Hanger and Fire Pump House. Reviewed design given by USACE. Performed Hydraulic Calculations in HASS. Revised designed drawings given by USACE to meet NFPA and UFC codes. Designed Seismic Brace system and performed calculations as per NFPA 13. Worked under the supervision of Fire Protection Specialist from USA.

 

Project Name: APS 500 Warehouses in Camp Arifjan (US Army)

​

Duration: April 2020 to October 2021.

​

This project consists of 05 Nos of typical Warehouses each of area 60,000 SQFT used for vehicle storage. It was protected by overhead wet pipe sprinkler system. Responsible for complete design of overhead sprinkler system. Designed Seismic Brace system and performed calculations as per NFPA 13.

Supervise Site Engineer for installation of Fire Protection Works. Worked under the supervision of Fire Protection Specialist from USA.

 

October 2013 to October 2019

​

Gulf Engineering Company, Kuwait

Gulf Engineering Company is one of the leading contracting and maintenance company in MEP services.

​

Designation : Project Engineer Plumbing and Fire Fighting

Delivered comprehensive execution of plumbing and firefighting systems across multiple high-profile projects, ensuring seamless project delivery from planning to commissioning.

Reviewed contract documents, BOQs, specifications, and design drawings to verify technical accuracy and compliance with project requirements.

​

Performed material take-offs, obtained competitive vendor quotations, and supported cost-effective procurement decisions.

Developed detailed price comparison sheets for internal evaluation and approval by the head office.

Prepared material submittals and ensured timely approvals from consultants through meticulous documentation.

Created accurate shop drawings and secured consultant approvals for site execution.

Led the successful execution of the Fawsec Campus at Sabah Al-Salem (Apr 2016 – Oct 2019), overseeing all MEP works.

Contributed significantly to the C4i/Main Support Building – KNPC Project at Ahmadi in two phases: Oct 2013 – Jul 2014 and Feb 2017 – Sep 2019.

Facilitated testing, commissioning, and preparation of As-Built drawings for projects in Egailla and Ahmadi NHC, ensuring alignment with project specifications.

Supervised the establishment of GEC’s New Workshop in Ahmadi, optimizing layout, resource allocation, and operational flow.
​

Major Project Highlights:

​

Project Name: Fawsec Campus at Sabah Al-Salem

​

Duration: Apr 2016- Oct 2019

​

Fawsec campus, located in Sabah Al Salem Area of Kuwait City, has been designed as a group of interconnected midrise buildings, providing residential units (190 one-bedroom apartments), leisure and activity units. The total built up area is approximately 19,000 sqm and the buildings are finished to the highest standards.

This building was protected by wet pipe sprinkler system and fire hose system. Building was fed by 02 Nos electric fire pump and 227 m3 water tank. I was responsible for creating shop drawings and material approval for Plumbing and Fire Fighting System. Submit Fire Fighting drawings for KFF approval. Prepare technical and price comparison sheet for head office approval. Supervised on-going work on site. Testing and commissioning. KFF approvals. Worked under a supervision of Sr. Project Engineer.

 

Project Name: C4i / Main Support Building in Ahmadi (Client: KNPC)

​

Duration: Oct 2013- July 2014 & Feb 2017 to Sep 2019

​

C4i (Command, Control, Communication, Computers and Intelligence) project with KNPC (Kuwait National Petroleum Company) at Al Ahmadi.

This building was protected by wet pipe sprinkler system and fire hose system. Fire Extinguishers were uniformly distributed all over the building. I was responsible for creating shop drawings and material approval for Plumbing and Fire Fighting System. Prepare technical and price comparison sheet for head office approval. Supervised on-going work on site. Testing and commissioning. KFF approvals. Worked under a supervision of Sr. Project Engineer.

 

Project Name: Egailla and Ahmadi NHC (Testing, Commissioning and As-Built Drawings)

It consists of Supermarket & Shops, Social Development Center, Banks, Library, Mosque, Clinic and some Governmental Offices.

Each buildings are protected by a combined wet sprinkler and standpipe system. In addition, clean agent automatic flooded type fire suppression system is used for HT and LT rooms. Generator room is protected by Foam System. Pillar hydrants are distributed all over.

 

Project Name: Gulf Engineering New Workshop in Ahmadi

This is a three story office building with one basement as workshop.
The building is protected by a combined wet sprinkler in basement and Fire Hose Cabinet (FHC) on upper floor. Fire Extinguishers are distributed all over the building.

 

November 2009 to July 2013

​

Contracting & Construction Enterprises, Riyadh, KSA

CCE is a leading construction company for civil and MEP works and classified as a first class general contracting company.

​

Designation : Project Engineer Plumbing and Fire Fighting
Executed plumbing and firefighting works with a strong focus on quality and safety.

Performed comprehensive material take-offs and meticulously prepared Bills of Quantities (BOQs) to support procurement and cost control.

Designed accurate shop drawings using AutoCAD, ensuring alignment with technical specifications and project coordination requirements.

Oversaw site operations for the Five-Star Hotel and Convention Center (ITCC Project), ensuring project execution met client and consultant standards.

Reviewed project specifications, IFC drawings, and site conditions, proactively identifying and resolving potential design conflicts or clashes.

Coordinated and submitted material submittals, securing timely approvals in accordance with project standards and authority regulations.

Raised and resolved technical queries (TQs) to clarify discrepancies in drawings and maintain uninterrupted site progress.

Prepared precise builder works drawings (MEP openings) for coordination with civil and structural works.

​

Project Highlights:

​

Project Name: Five Star Hotel and Convention Center (ITCC)

This project calls for construction of Five Star Hotel and Convention Centre. The hotel will include 230 rooms and 40 suits. The package includes construction of 3 basements (for parking), ground & mezzanine floor and 5 storey hotel rooms & suits. Basement to Ground Floor Area=36,000 m²& 1st Floor to 5th Floor Area = 2,664 m².

Project Value: 150 Million US$.

 

The building is protected by a combined wet sprinkler and standpipe system. In addition, clean agent automatic flooded type fire suppression system is used for server rooms, electrical rooms, communication rooms, etc. Portable fire extinguishers are distributed in corridors and designated areas.

• Study of project specifications and drawings

• Review material submittals and approvals

• Prepare technical queries for shop drawings clarifications

• Prepare builder works (MEP Openings) drawings

• Supervise mechanical work on the site and make sure that work is executed as per approved drawings

• Material take-off and prepare schedule of requirements

• Track on material deliver on site in time

• Created shop drawings for plumbing and fire protection.

​

​

October 2005 to August 2009

​

AMIN Contraction Pvt. Ltd, Male, Maldives
Amin construction is contracting company for civil and MEP works in residential, commercial and resort projects in Maldives.

​

Designation : Mechanical Engineer

Developed detailed plumbing and firefighting shop drawings in AutoCAD and secured final consultant approvals, ensuring compliance with technical specifications and project standards.

Produced accurate as-built drawings for plumbing, firefighting, and electrical systems, facilitating smooth handover and future maintenance.

Conducted thorough material take-offs, enabling efficient planning, procurement, and cost control.

Oversaw construction of the 14-story Velaanage Government Office Building, ensuring project milestones were met within timeline and budget.

Reviewed contract documents, designs, and IFC drawings to identify discrepancies and ensure industry-standard compliance.

Compiled and submitted a complete and well-organized set of documentation for final authority approvals and handover.

​

Project Highlights:

​

Project Name: Fourteen Story Velaanage Office Building, Male

1. Study of contract document, designs and drawings.

2. Prepare plumbing and firefighting shop drawings in AutoCAD
3. Preparing plumbing, electrical and air-conditioning schedule & material requirements

4. Create fire protection riser diagrams

5. Co-ordination with sub-contractors and consultants
6. Responsible for preparing daily, weekly and monthly progress repor

 

Project Name : Five Storey Basic Blocks Hulmale – Block 1 (Residential Building)

1. Create as-built drawings of plumbing, electrical and fire-fighting.
2. Meet with client to discuss these drawings.

3. Prepare a organized set and submit these drawings for approval

​​

August 2002 to September 2005

​

Smart Conveyor Design Solutions Pvt Ltd
(Aerowerks Inc, Canada)

Position : Mechanical CAD Engineer
 

Smart Conveyor Design Solutions Pvt Ltd (Aerowerks Inc, Canada) – Specializes in the design and manufacturing of customized material handling system for dish room & food service industry. To meet growing business needs, Aerowerks opened an office in Chandigarh.

 

Successfully supported business development efforts, helping Aerowerks establish a fully functional design and customer service office in India to support Canadian operations.

Reviewed and checked presentation drawings in AutoCAD, ensuring accuracy and quality before submission to the Toronto head office.

Created, reviewed, and validated fabrication and production drawings in AutoCAD and SolidEDGE, providing final deliverables for the Canadian manufacturing team.

Maintained daily coordination with Canadian project teams, ensuring real-time communication and alignment on design expectations.

Trained and mentored a team of graduate engineers, enhancing their technical capabilities and ensuring consistent quality in design outputs